Mask GloUpdated 3 hours ago

Shop TheraFace Mask Glo

Efficient. Effective. Effortless. 

Key Product Features

• Red, red + infrared and blue LED light
• 504 LED lights for full face coverage
• Vibration for relaxing scalp massage
• Cordless design for hands-free treatment
• Lightweight at 514g
• Fast treatment times of 4-12 minutes

What's included in box?

• TheraFace Mask Glo device
• Protective eye shield
• USB-C charging cable

Using Your Device

Before beginning your treatment charge your TheraFace Mask.

1. Prepare for treatment. Begin with a clean, dry face. Do not allow the device to come in contact with colored solids or liquids, as it is hard to clean after being dyed. Remove all makeup, wash hands thoroughly, and ensure that cosmetics (such as lipstick) and oils do not contact the device. 
2. Put on the device. Place the device on your face, and adjust both of the Velcro straps to your desired fit. The device should fit snug but not too tight on your face.
3. Turn on the device. Press and hold the LED power button to begin a light and vibration treatment. Press and hold the power button to turn on the vibration treatment only. At any point during the light and vibration treatment, press and hold vibration button to turn off the vibration for light treatment only.  
4. Select your desired LED light treatment setting. The device will guide you through a 12-minute science-backed treatment that automatically cycles through three LED light treatment types; red light, red + infrared light, and blue light. Each treatment will be 4 minutes long. Press the LED power button at any point to cycle through light therapy types. You will hear a beep when the light therapy type changes. 
5. Select your desired vibration treatment setting. There are two vibrating motors located in the headstrap. Press the vibration button to toggle through the three modes (Relax: low-frequency continuous; Refresh: higher-frequency continuous, and Relieve: wave). Use vibration as a standalone treatment without LED light be pressing and holding the LED button while vibration is on. If vibration is used as a standalone treatment, it will run for 12 minutes.
6. Sit back and enjoy. Relax and enjoy your treatment. 
7. Turn off the device. Press and hold the power button at any point during the treatment to turn off the device. The LED light will turn off when the device is off. The device will automatically shut off after 12-minute treatment is complete.

This device has built-in eyeshields. Normal use of the eyeshields may result in redness around your eye area. Some redness is normal and should subside within 5-10 minutes of using this device. 

Recommended Use: 6 Days per week. To learn more about the science and benefits behind the modalities included in this device, visit us here: https://www.therabody.com/pages/science.

Charging and LED Indicator Guide

The device is USB-C enabled and comes with a charging cable. Before charging, ensure the device is powered off. 

• Connect one end of the charging cable to the USB-C charging port of the device. It is located on the side of the device. Connect the other end of the charging cable to a power adapter (not included).
• The LED light will indicate the battery status when the device is on or charging. Turn on the device to check the battery status.
  • Flashing Orange: Recharge
  • Solid Orange: Low battery
  • Sold Green: High battery

The battery life of the device is up to 60 minutes depending on the settings used. Use a USB-C power adapter of at least 20W when charging the device. 

Care and Cleaning

• Before cleaning, turn off the device. Ensure that the device is not connected to a charging cable or a power source before cleaning. 
• The TheraFace Mask Glo is not waterproof. Do not submerge the device in water or clean it under running water.  Do not apply excessive cleaning solutions, which can damage the device's appearance and function. 
• Wipe off any visible dirt with a disposable cloth moistened with a mild detergent. Be sure to wipe the interior surfaces of the mask. Next, use a soft cloth dampened with 70% isopropyl alcohol to wipe and disinfect the mask for three (3) minutes, especially the inner surface of the mask. Repeat this process three times. Finally, wipe the disinfectant with a clean, dry cloth or towel until there is no visible residue.
• After cleaning, allow the device to dry thoroughly before storing or beginning another treatment. A properly cleaned device should have no visible signs of debris or moisture.
• For best hygiene practice, clean the device after every use.

Specifications

User Manual

TheraFace Mask Glo User Manual and Unit Warnings